MTCPM Project HOWTOs - Revision history

Jhoger: Project HOWTOs moved to MTCPM Project HOWTOs

2009-02-20T23:40:31Z

Project HOWTOs moved to MTCPM Project HOWTOs

← Older revision	Revision as of 16:40, 20 February 2009
(No difference)

206.169.229.170 at 23:38, 20 February 2009

2009-02-20T23:38:02Z

← Older revision		Revision as of 16:38, 20 February 2009
Line 40:		Line 40:
	DONE! you are now running CP/M.		DONE! you are now running CP/M.

	[[Category:mtcpm]]		[[Category:mtcpm]] [[Category:VirtualT]]

206.169.229.170 at 23:37, 20 February 2009

2009-02-20T23:37:36Z

← Older revision		Revision as of 16:37, 20 February 2009
Line 39:		Line 39:

	DONE! you are now running CP/M.		DONE! you are now running CP/M.

			[[Category:mtcpm]]

78.69.53.223 at 19:48, 20 February 2009

2009-02-20T19:48:47Z

← Older revision		Revision as of 12:48, 20 February 2009
Line 18:		Line 18:
	Now, you should see Map 0, 100-13F OPT with data 0x1820, 0x1821 etc		Now, you should see Map 0, 100-13F OPT with data 0x1820, 0x1821 etc

	Finally, select ~~Same~~ Map on the left, and close the window.		Finally, select Save Map on the left, and close the window.

	5) loading a CP/M image into the "option rom"		5) loading a CP/M image into the "option rom"

Jhoger: New page: Here is a list of how to set up all ram mode. 1) start VT 1.3 2) emulate M100 or T102, whatever 3) turn on ReMem emulation - Emulation --> Memory options: select ReMem, click ok 4)...

2008-12-28T18:18:48Z

New page: Here is a list of how to set up all ram mode. 1) start VT 1.3 2) emulate M100 or T102, whatever 3) turn on ReMem emulation - Emulation --> Memory options: select ReMem, click ok 4)...

New page

Here is a list of how to set up all ram mode.

1) start VT 1.3

2) emulate M100 or T102, whatever

3) turn on ReMem emulation -
Emulation --> Memory options: select ReMem, click ok

4) configure ReMem : tools --> remem configuration:
- first, click Default Map - this will do an initial set up
- next, on the left column, select MAP0
- on the second left column, sleect 100-13F OPT
- on the right, de-check sector lock, De-check RAM CS, check Flash 1
and check flash 2
- map data should be unchanged, and read 0x020
- select copy sequential
Now, you should see Map 0, 100-13F OPT with data 0x1820, 0x1821 etc

Finally, select Same Map on the left, and close the window.

5) loading a CP/M image into the "option rom"
- tools --> memory editor
- select region RAM
- File --> load from file
- enter the full path name for the binary CP/M image
- start address should be 0x008000
- select ok

Now, the binary image is loaded at offset 008000 in the RAM region.
You can check this by scrolling down.

6) activating the CP/M option rom
- enter BASIC
- type OUT 112,1
(this activates ReMem map 00)
- type CALL63012
(this will start the option ROM)

DONE! you are now running CP/M.