Bitchin100 DocGarden - User contributions [en]

Format Your Words With This TEXT Aid

2009-01-25T19:39:39Z

97.89.182.164:

With a little Basic help, your 100 can be a hot-shot word processor.
By RICHARD RAMELLA
Portable 100/September 1983
Page 27-28
____
Though its text-handling capabilities are diverse, the Model 100's built-in, word-processing program lacks features needed by many wordsmiths. So I wrote TEXTHELPER, a fairly short basic program that formats printed documents in useful ways.

With this program, you may set side margins from 0 to 20, single-, double- or triple-space, and print page numbers, headers, and footers. The text is automatically printed in a spaced format so it continues from page to page with uniform margins at top and bottom. It is for use with standard 8 l/z-by-11 -inch paper.

And just to show you my heart's in the right place, I've thrown in a little routine that counts the words in a document.

FASTER THAN HAND. The format printing process occurs quite slowly by computer standards but still is perhaps 10 times faster than the human hand and unerring in following your instructions. Sophisticated and lightning quick word processing is on the horizon for the Model 100, but those programs you won't get for the cost of a few magazine pages.

The experts may want to skip ahead here, because I'm starting at the beginning for the many Model 100 owners just getting acquainted with their machine.

The Model 100 has several kinds of files. The two we'll deal with are text documents and Basic programs. The program TEXTHELPER is a Basic program. It calls up material in a text file and sends it to the line printer, which prints it on paper in the format you have determined.

What you need to know about creating a text file is in chapter eight (pages 43-60) of the manual that came with the computer. Once you are able to create a text file, write words in it, and save the file, you can use this program.

MENU MODE, In the menu mode, the text file you create will be followed by the file name extension .DO. Using TEXTHELPER, you may call up only .DO files for formatting.

Before you Run TEXTHELPER, there, must be a text file in the system, and you must know the exact name of it. This isn't difficult because you named the file when you created it.

A note of caution is warranted here. When you create the text file, make sure you don't use the tab key on your 100. And although your typing teacher may have taught you to leave two spaces between sentences, don't do it here. The results will be bizarre.

Let's say you want to format a file listed in the menu as MOM.DO. (It's a long overdue letter to your poor old gray-haired mother.)

This program is so user-friendly many experienced computer jockeys are going co be kicking out program lines left and right. But it protects the novice computer user from mistakes in numerous ways.

As the program begins, a two-item menu is shown. Type 1 and tap enter to try the word counter. Or type 2 and tap enter to try the document formatter. Tap anything else and you must try again until you get one of the two acceptable answers.

WORD COUNTER. If you try the word-counter routine, it asks for the name of the file to be accessed. The file name is MOM.DO, but you just type in the word MOM in any mix of upper and lower case, and the machine understands. The program displays WORDS: followed by a number that grows as each word is counted. When it's through counting, you know it because you're told Tap "M" to return to "MENU."

The document formatting pan of the program is more complex in its workings but not complex in use.

DECISIONS, DECISIONS. To format, you must make several decisions. I'll list them in turn:
• You're asked what margin from 0 to 20 you wish. A choice less than zero or more than 20 is unacceptable. Paper sized at 8 1/2-by-ll inches will hold about 85 characters on a line. Note that 9 1/2-by-11-inch computer paper is actually 8 1/2 inches wide after you tear off the tractor-feed margins. If your line printer allows changing the width of letters, I advise you to set it at 10 characters per inch so 85 characters fit snugly between one edge and the other. Otherwise, this program may give you unintended results.

The number you choose for a left margin is exact but on the right it is approximate. Both are about the same, but the right margin allows a bit of grace. This is because the program doesn't go to the next line until it encounters a line feed or blank space occurring after passing the line length determined by the margins it passed. This prevents line feeds in mid-word.

• That brings us to the next choice. If you select a right margin of 10 and a left margin of 10, then you'll have a line with about 65 characters (85 minus 20) in it. The program tells you this and asks: "Is this okay?" If it isn't, type N for no and tap Enter.

You'll get another try at setting margins and may keep trying until satisfied. Answering Y for yes sends the program onward.
• A menu for line spacing is shown. Your choices are 1 for single space. 2 for double space, and 3 for triple space. If you are printing a single-spaced document on a single page, it's better to use the print function included with the Model 100's text-processing program. Single-spaced text gives you 50 lines a page, double-spaced 25 lines, and triple-spaced 16 lines.

• Now choose your header. A header is just word-processing jargon for a title. You don't need a header on a letter to mom, but in other cases it's very useful: War and Peace — Fifth Draft... Annual Report... and the like. You are given a limit here for the number of characters you may put in the header. It's based on the number of characters in the formatted line. If your header is too long, you get a chance to write a shorter one. In fact, it's mandatory.

The header also includes three other interesting things: the date, the time, and the page number. These are provided automatically. I'm afraid that by including the exact time on each page, I've revealed exactly how slow this program can be - more than two minutes for a double-spaced page 65 characters wide.

• The final format choice is the footer. It goes below the final line on the page and approximately flush with the right of that line. A footer may say (MORE), (CONTINUED) or any other message you want on each page. Don't make It too long; if it is longer than the number of characters in your line, you may get an error message and a crashed program. Trusting you to follow this advice, I have not built in a rescue should your footer exceed the number of characters in the line.

GENTLE REMINDER. Now the program reminds you to turn on the printer and position the paper. On my ancient Line Printer III the paper is positioned if the top of the print head is even with the perforation across the top of the first fan-fold page on which I will he printing.

You may have to experiment for the best setting on your printer.On the same screen display as your final reminders are the words: "Enter name of text file to be formatted." In our hypothetical case, we type the word "mom" and stand back for some turtle-like formatted printing.

If your printer doesn't jam the first time you look away from it, you might go into the kitchen for milk and cookies while it does its work. You can get pretty bored watching this program run - even when it's printing your own deathless words.

<pre>
100 REM*TEXTHELPER*
101 REM*TRS-80 Model 100*
102 REM*By Richard Romella*
110 CLS
120 PRINT"Menu:"
130 PRINT STRING$(24,"-")
140 PRINT"1-Word Counter"
160 PRINT"2-DocumentFormatter"
170 PRINT STRING$(24,"-")
180 INPUT"Number of your choice";A
190 IF A<>1 AND A<>2 THEN CLS:PRINT"Choiceslimitedlo...":GOTO 120
200 CLS:H=0:P=0
210 IF A=2 THEN 340
220 REM*WordCountRoutine*
230 W=1
240 INPUT “Name of file for word count";N$
250 OPEN N$ FOR INPUT AS 1
260 A$=INPUT$(1,1)
270 Z$=Z$+A$
280 N=N+1
290 IF N>3 THEN Z$=RIGHT$(Z$,3)
300 IF EOF(1) THEN 780
310 IF A$=CHR$(10) THEN W=W+1
311 IF LEFT$(Z$,1)<>CHR$(32) AND MID$(Z$,2,1)=CHR$(32) AND RIGHT$(Z$,1)<>CHR$[32)THEN W=W+1
320 PRINT @165,”WORDS:”;W
330 GOTO 260
340 REM* Document Formatter *
350 INPUT”Margin width (0 to 20)”;M
360 IF M<0 OR M>20 THEN CLS: PRINT "Note limits”: GOTO 350 ELSE M=INT(M):CLS
370 WL=85-{M*2)
380 PRINT"Margins of”M"left and right yield"
390 PRINT”a line of about ”WL” characters.”
400 INPUT”Is this okay(y/n)”;G$
410 IF G$<>”y” AND G$<>"Y" AND G$<>”n” AND G$<>”N" THEN CLS:GOTO 380
420 IF G$-"n" OR G$-"N"THEN CLS:GOTO 350 ELSE CLS
430 PRINT "Spacing:"
440 PRINT STRING$(15,"-”)
450 PRiNT”1-single”
460 PrlNT”2-double"
470 PRINT”3-triple"
480 PRINTSTRING$(15,"-")
490 INPUT”Choose 1, 2or 3”;SP
500 IF SP<>1 AND SP<>2 AND SP<>3 THEN CLS:GOTO 430 ELSE CLS
510 PRINT”Header up to”WL-19"characters”
520 INPUT”Header choice";HE$
530 IF LEN(HE$)>WL-19 THEN CLS:PRINT HE$:PRINT”too long.”:PRINT:GOTO510
540 CLS
550 INPUT”Footer choice”;FO$
560 CLS 5
570 PRINT”Line printer on? Paper positioned?"
580 PRINT”Enter name of text file to be formated."
590 INPUT N$
600 P=1
610 FOR A=1 TO 4
620 LPRINT
630 NEXT
640 XX=1
650 GOSUB 880
660 LPRINT
670 LPRINT
680 OPEN N$ FOR INPUT AS 1
690 LPRINT SPACE$(M);
700 A$=INPUT$(1,1)
710 IF EOF(1) THEN PRINT”Document has been printed in chosen format.":GOTO 780
720 LPRINT A$;
730 H=H+1
740 IF H>WL AND A$=CHR$(32) THEN FOR=1 TO SP:LPRINT:J=J+1:NEXT V:LPRINT SPACE$(M);:H=0
750 IF A$=CHR$(10) AND SP>1 THEN J=J+1:FOR V=1 TO SP-1:LPRINT:J=J+1:NEXT V:LPRINT SPACE$(M);:H=0:ELSE IF A$=CHR$(10)THEN J=J+1:H=0:LPRINT SPACE$(M);
760 IF SP-1 AND J-50 OR SP-2 AND J-50 OR SP=3 AND J=48 THEN GOSUB 810
770 GOTO 700
780 CLOSE 1
790 PRINT@240,"Tap M to return to MENU"
800 IF INKEY$=”” THEN 790 ELSE 110
810 LPRINT
820 LPRINT
830 LPRINT SPACE$(85-(M+LEN(FO$))),FO$
840 FOR S=1 TO 8
850 LPRINT
860 NEXTS
870 IF SP=3 THEN LPRINT:LPRINT
880 J=00:IF XX=0 THEN P=P+1
890 LPRINT SPACE$(M);CHR$(32);HE$;CHR$(32);CHR$(32);DATE$,CHR$(32);TIME$;SPACE$(3);P
900 LG=LEN(HE$+CHR$(32)+DATE$+CHR$(32)+TIME$;SPACE$(7))
910 LPRINT SPACE$(M);STRING$(LG,"-")
920 IF XX=1 THEN XX=0:RETURN
930 FOR S=1 TO 3
940 LPRINT
950 NEXTS
960 LPRINT SPACE$(M);
970 RETURN
980 END
</pre>

[[Category:Model 100 Classics]]

Category:Model 100 Classics

2009-01-25T00:59:55Z

97.89.182.164: Format Your Words With This Text Aid, By RICHARD RAMELLA Portable 100/September 1983

Format Your Words With This Text Aid

With a little Basic help, your 100 can be a hot-shot word processor.
By RICHARD RAMELLA
Portable 100/September 1983
Page 27-28
____
Though its text-handling capabilities are diverse, the Model 100's built-in, word-processing program lacks features needed by many wordsmiths. So I wrote TEXTHELPER, a fairly short basic program that formats printed documents in useful ways.

With this program, you may set side margins from 0 to 20, single-, double- or triple-space, and print page numbers, headers, and footers. The text is automatically printed in a spaced format so it continues from page to page with uniform margins at top and bottom. It is for use with standard 8 l/z-by-11 -inch paper.

And just to show you my heart's in the right place, I've thrown in a little routine that counts the words in a document.

FASTER THAN HAND. The format printing process occurs quite slowly by computer standards but still is perhaps 10 times faster than the human hand and unerring in following your instructions. Sophisticated and lightning quick word processing is on the horizon for the Model 100, but those programs you won't get for the cost of a few magazine pages.

The experts may want to skip ahead here, because I'm starting at the beginning for the many Model 100 owners just getting acquainted with their machine.

The Model 100 has several kinds of files. The two we'll deal with are text documents and Basic programs. The program TEXTHELPER is a Basic program. It calls up material in a text file and sends it to the line printer, which prints it on paper in the format you have determined.

What you need to know about creating a text file is in chapter eight (pages 43-60) of the manual that came with the computer. Once you are able to create a text file, write words in it, and save the file, you can use this program.

MENU MODE, In the menu mode, the text file you create will be followed by the file name extension .DO. Using TEXTHELPER, you may call up only .DO files for formatting.

Before you Run TEXTHELPER, there, must be a text file in the system, and you must know the exact name of it. This isn't difficult because you named the file when you created it.

A note of caution is warranted here. When you create the text file, make sure you don't use the tab key on your 100. And although your typing teacher may have taught you to leave two spaces between sentences, don't do it here. The results will be bizarre.

Let's say you want to format a file listed in the menu as MOM.DO. (It's a long overdue letter to your poor old gray-haired mother.)

This program is so user-friendly many experienced computer jockeys are going co be kicking out program lines left and right. But it protects the novice computer user from mistakes in numerous ways.

As the program begins, a two-item menu is shown. Type 1 and tap enter to try the word counter. Or type 2 and tap enter to try the document formatter. Tap anything else and you must try again until you get one of the two acceptable answers.

WORD COUNTER. If you try the word-counter routine, it asks for the name of the file to be accessed. The file name is MOM.DO, but you just type in the word MOM in any mix of upper and lower case, and the machine understands. The program displays WORDS: followed by a number that grows as each word is counted. When it's through counting, you know it because you're told Tap "M" to return to "MENU."

The document formatting pan of the program is more complex in its workings but not complex in use.

DECISIONS, DECISIONS. To format, you must make several decisions. I'll list them in turn:
• You're asked what margin from 0 to 20 you wish. A choice less than zero or more than 20 is unacceptable. Paper sized at 8 1/2-by-ll inches will hold about 85 characters on a line. Note that 9 1/2-by-11-inch computer paper is actually 8 1/2 inches wide after you tear off the tractor-feed margins. If your line printer allows changing the width of letters, I advise you to set it at 10 characters per inch so 85 characters fit snugly between one edge and the other. Otherwise, this program may give you unintended results.

The number you choose for a left margin is exact but on the right it is approximate. Both are about the same, but the right margin allows a bit of grace. This is because the program doesn't go to the next line until it encounters a line feed or blank space occurring after passing the line length determined by the margins it passed. This prevents line feeds in mid-word.

• That brings us to the next choice. If you select a right margin of 10 and a left margin of 10, then you'll have a line with about 65 characters (85 minus 20) in it. The program tells you this and asks: "Is this okay?" If it isn't, type N for no and tap Enter.

You'll get another try at setting margins and may keep trying until satisfied. Answering Y for yes sends the program onward.
• A menu for line spacing is shown. Your choices are 1 for single space. 2 for double space, and 3 for triple space. If you are printing a single-spaced document on a single page, it's better to use the print function included with the Model 100's text-processing program. Single-spaced text gives you 50 lines a page, double-spaced 25 lines, and triple-spaced 16 lines.

• Now choose your header. A header is just word-processing jargon for a title. You don't need a header on a letter to mom, but in other cases it's very useful: War and Peace — Fifth Draft... Annual Report... and the like. You are given a limit here for the number of characters you may put in the header. It's based on the number of characters in the formatted line. If your header is too long, you get a chance to write a shorter one. In fact, it's mandatory.

The header also includes three other interesting things: the date, the time, and the page number. These are provided automatically. I'm afraid that by including the exact time on each page, I've revealed exactly how slow this program can be - more than two minutes for a double-spaced page 65 characters wide.

• The final format choice is the footer. It goes below the final line on the page and approximately flush with the right of that line. A footer may say (MORE), (CONTINUED) or any other message you want on each page. Don't make It too long; if it is longer than the number of characters in your line, you may get an error message and a crashed program. Trusting you to follow this advice, I have not built in a rescue should your footer exceed the number of characters in the line.

GENTLE REMINDER. Now the program reminds you to turn on the printer and position the paper. On my ancient Line Printer III the paper is positioned if the top of the print head is even with the perforation across the top of the first fan-fold page on which I will he printing.

You may have to experiment for the best setting on your printer.On the same screen display as your final reminders are the words: "Enter name of text file to be formatted." In our hypothetical case, we type the word "mom" and stand back for some turtle-like formatted printing.

If your printer doesn't jam the first time you look away from it, you might go into the kitchen for milk and cookies while it does its work. You can get pretty bored watching this program run - even when it's printing your own deathless words.

100 REM*TEXTHELPER*
101 REM*TRS-80 Model 100*
102 REM*ByRichardRomella*
110 CLS
120 PRtNT"Menu:"
130 PRINTSTRING$(24,"-")
140 PRINT"1-Word Counter"
160 PRINT"2-DocumentFormatter"
170 PRINTSTRING$(24,"-")
180 INPUT"Number of your choice";A
190 IFA<>1ANDA<>2THENCLS
:PRINT"Choiceslimitedlo..."
:GOTO120
200 CLS
:H=0
:P=0
210 IFA=2THEN340
220 REM*WordCountRoutine*

Category:Model 100 Classics

2009-01-22T23:14:39Z

97.89.182.164: ROM ADDRESSES: GETTING BASIC TO DO WHAT YOU WANT [PORTABLE 100 - September 1983..FW

How does Basic do what you tell it to do? Clues to the language's subservience lie in ROM.
By JAKE COMMANDER
How on earth does Basic know what to do? All those statements, commands, and functions, yet the interpreter untiringly plods through your code always knowing what's required next. Just how does it do it?

Well, if the answer were simple, everybody would be writing Basic interpreters and putting Microsoft out of business. But it is possible to follow at least some of the pathways Basic uses to perform its duties.

Most addresses of the ROM routines which comprise Basic are held in two tables. These can be unravrelled to give a list of routines used to perform various tasks.

JUMP ADDRESSES. One table contains jump addresses for the commands ( or verbs, as it were) which will always be the first thing the interpreter picks up from a statement. The whole repertoire of such commands is catered for the table located at 0262 hex.

Basic gets the appropriate jump address by using the token number for the command it's about to execute. All tokens are numbers from 128 to 255; therefore subtracting 128 gives numbers from zero to 127. As each jump address in the table is two bytes long, the token (minus 128) is multiplied by two to give an offset into the table. This points straight at the address which is needed. The two-byte address is picked up and jumped to ― and we're now executing a Basic command in pure machine code.

What happens next depends entirely on the machine code for the command itself. Various syntaxes are allowed for some commands but not for others. For instance, the print command would allow an expression such as TAB(22);l/3 , so would an LPR1NT. But a LET would have none of that. LET X = TAB(22); 1/3 would have you on the carpet in no time.

Also various combinations of tokens can do different things. The comparison operators, for example, can be used pretty much interchangeably. These operators, >― <> = < , etc are all OK syntactically. This versatility means a table for such a wide set of possibilities is nigh impossible.

SECOND TABLE However, there is a second table at location 004E in the ROM. This contains many addresses used in the evaluation of Basic math functions and expressions. These are extracted and jumped to in a similar fashion to the first table.

Any Basic word excluded from either of these tables is handled separately by the interpreter according to its particular use. However, out of a possible 128 tokens, these two tables give us a mechanism by which we can follow the machine-code execution of many of them. It is the combination of these routines and the syntax checking required to logically execute them that makes up an interpreter.

The following list has been compiled from the two tables I've described and a disassembly of other parts of the ROM. It shows the entry points for all important Basic statements and functions. Certain functions can have more than one possible syntactic use and the list does not cover all such uses. (An example is the statement OFF, which can be SOUND OFF or MOTOR OFF etc.) The list is in four columns. The first is the address in ROM where the Basic word occurs in the vocabulary table. The second entry is the word itself. Third is the token assigned to that word when it is encoded by the Basic interpreter.

FOURTH COLUMN. The fourth column contains the address the interpreter jumps to to execute the token representing the statement or function desired. Once again, some statements can have more than one use such as MID$ (LH$)=RH$, and LH$=MID$ (RH$). In these cases, two addresses are given: one for use on the left hand side of the equals sign and one for the right hand side of the sign.

Perhaps unsurprisingly, things get a little more complicated with the mathematical functions in Basic. It's not simply a matter of taking an address for, say, a multiply routine and then jumping to it. The Basic interpreter has to know the numeric type of operator it has to work on. For instance, with the addition operator, Basic has four choices: signed integer, single precision, double precision, and string. None of the other binary operators allow string manipulation, so they're limited to the numeric variable types only.

The addresses of these binary operators can be confirmed (if you need confirmation) from three short tables in ROM ― one each for double precision, single precision, and integer numbers respectively.

The tables contain six addresses apiece for addition, subtraction, multiplication, division, exponentiation, and comparison. Rather than clutter the token-addresses table, these addresses are contained separately at the end.

In a following article, I'll be looking at ways to use some of these addresses in your own machine-code programs. For the more adventurous, an experiment will probably prove irresistible. Remember, though, in a RAM-file machine such as the Model 100, a lock-up may cost you all your files. Use caution.

JAKES ROM ADDRESSES FOR BASIC KEYWORDS

0080 => END = 80 @ 409F

0083 => FOR = 81 @ 0726

0086 => NEXT = 82 @ 4174

008A => DATA = 83 @ 099E

008E => INPUT = 84 @ 0CA3

0093 => DIM = 85 @ 478B

0096 => READ = 86 @ OCD9

009A => LET = 87 @ 09C3

009D => GOTO = 88 @ 0936

OOA1 => RUN = 89 @ 090F

OOA4 => IF = 8A @ OB1A

OOA6 => RESTORE = 8B @ 407F

00AD => GOSU8 = 8C @ 091E

0082 => RETURN = 8D @ 0966

OOB8 => REM = 8E @ 09AO

OOBB => STOP = 8F @ 409A

OOBF => WIDTH = 9D @ 1DC3

OOC4 => ELSE = 91 @ 09AO

OOC8 => LINE = 92 @ OC45

OOCC => EDIT = 93 @ 5E51

OODO => ERROR = 94 @ OBOF

00D5 => RESUME = 95 @ OABO

OODB => OUT = 96 @ 11OC

OODE => ON = 97 @ OA2F

OOEO => DSKOS = 98 @ 5071

OOE5 => OPEN = 99 @ 4CCB

OOE9 => CLOSE = 9A © 4E20

OOEE => LOAD = 98 @ 4D70

OOF2 => MERGE = 9C @ 4D71

OOF7 => FILES = 9D @ 1F3A

OOFC => SAVE = 9E © 4DCF

0100 => LFILES = 9F @ 506F

0106 => LPRINT = AO @ OB4E

010C => DEF = A1 @ 0872

010F => POKE = A2 @ 128B

0113 => PRINT = A3 @ 0B56

0118 => CONT = A4 @ 40DA

011C => LIST = A5 @ 1140

0120 => LLIST = A6 @ 113B

0125 => CLEAR = A7 @ 40F9

012A => CLOAD = A8@ 2377

012F => CSAVE = A9 @ 2280

0134 => T1ME$ = AA @ 19AB 1904

0139 => DATES = AB @ 19BD 1924

013E => DAYS = AC © 19F1 1955

0142 => COM = AD @ 1A9E

0145 => MDM = AE @ 1A9E

0148 => KEY = AF @ 1BB8

014B => CLS = BO @ 4231

014E => BEEP = B1 @ 4229

0152 => SOUND = B2 @ 1DC5

0157 => LCOPY = B3 @ 1E5E

015C => PSET = B4 @ 1C57

0160 => PRESET = B5 @ 1C66

0166 => MOTOR = B6 @ 1DEC

016B => MAX = B7 @ 7FOB 19DB

016E => POWER = B8 @ 1419

0173 => CALL = B9 @ 1DFA

0177 => MENU = BA @ 5797

017B => IPL = BB @ 1A78

017E => NAME = BC @ 2037

0182 => KILL = BD @ 1F91

0186 => 3CREEN = BE @ 1E22

018C => NEW = BF @ 20FE

018F => TAB( = CO @ OC01
�
0193 => TO = C1 @ 076B

0195 => USING = C2@ 4991

D19A => VARPTR = C3 @ OF7E

01AO => ERL = C4@ OF56

01 A3 => ERR = C5@ OF47

01 A6 => STING$ = C6@ 296D

01 AD => INSTR = C7 @ 2A37

0182 => DSKI$ = C8 @ 5073

01B7 => INKEY$ = C9@ 4BEA

01BD => CSRLIN = CA@ 1D90

01C3 => OFF = C8 @ various

01C6 => HIMEM = CC @ 1DB9

01CB => THEN = CD® OB2A

01CF => NOT = CE @ 1054

01D2 => STEP = CF @ O783

01 06 => + = D0 *

01D7 => - = D1 * See

01D8 => * = D2 * table

01 D9 => / = D3 * at end

010A => /\ = D4 *

01 DB => AND = D5 @ 1097

01 DE => OR = 06 @ 108C

O1EO => XOR = D7 @ 10A2

01E3 => EQV = D8 @ 10AD

01E6 => IMP = D9 @ 10B5

01E9 => MOD = DA@ 37DF

01 EC => \ = DB @ 377E

01ED => > = DC@ OE29

01EE => = = DD@ OE29

01EF => < = DE @ OE29

01FO => SGN = DF @ 3407

01F3 => INT = E0 @ 3654

OIF6 => ABS = E1 @ 33F2

01F9 => FRE = E2 @ 2B4C

01FC => INP = E3 @ 1100

01FF => LPOS = E4 @ 10C8

0203 => POS = E5 @ 10CE

0206 => SQR = E6 @ 305A

0209 => RND = E7 @ 313E

020C => LOG = E8 @ 2FCF

020F => EXP = E9 @ 30A4

0212 => COS = EA @ 2EEF

0215 => SIN = EB @ 2F09

0218 => TAN = EC @ 2F58

021B => ATN = ED @ 2F71

021E => PEEK = EE @ 1284

0222 => EOF = EF @ 1889

0225 => LOG = F0 @ 506D

0228 => LOF = F1 @ 506B

022B => CINT = F2 @ 3501

022F => CSNG = F3 @ 352A

0233 => CDBL = F4 @ 35BA

0237 => FIX = F5 @ 3645

023A => LEN = F6 @ 2943

023D => STR$ = F7 @ 273A

0241 => VAL = F8 @ 2A07

0244 => ASC = F9 @ 294F

0247 => CHR$ = FA @ 295F

0248 => SPACE$ = FB @ 298E

0251 => LEFT$ = FC @ 29AB

0256 => RIGHT$ = FD @ 29DC

025C => MID$ = FE @ 2AC2 29E6

0260 => ' = FF @ OA90

+ - * / > Cmpr
D.P. 2B78 2B69 2CFF 2DC7 3D8E 34FA
S.P. 37F4 37FD 3803 380E 3D7F 3498
INT 3704 36F8 3725 OFOD 3DF7 34C2
Siring 28CC 270C

Portable lO0 September 1983