Splitting the Model 100/102/200 case - Revision history

Jhoger at 16:20, 23 February 2009

2009-02-23T16:20:03Z

← Older revision		Revision as of 09:20, 23 February 2009
Line 49:		Line 49:
	out! The screen side slides downward from the back side. Once off,		out! The screen side slides downward from the back side. Once off,
	remove the 4 screws that hold the LCD into the whatchamacallit.		remove the 4 screws that hold the LCD into the whatchamacallit.

			[[Category:Model T Hardware Hacking]]

64.81.88.222: /* SPLITTING THE MODEL 100 CASE (The 102 and 200 split the same way) */

2008-03-10T05:19:01Z

SPLITTING THE MODEL 100 CASE (The 102 and 200 split the same way)

← Older revision		Revision as of 22:19, 9 March 2008
Line 3:		Line 3:
	From the Club 100 support files (www.club100.org)...		From the Club 100 support files (www.club100.org)...

	There is a trick to splitting the Model 100 case: The two halves of the case		There is a trick to splitting (opening) the Model 100 case: The two halves of the case
	are held together by plastic notches in the middle of the edges. After		are held together by plastic notches in the middle of the edges. After
	removing the case screws you simply have to know where to push in on the case		removing the case screws you simply have to know where to push in on the case

64.81.88.222: /* More Details from RickHanson on the T200 */

2008-03-10T05:18:34Z

More Details from RickHanson on the T200

← Older revision		Revision as of 22:18, 9 March 2008
Line 20:		Line 20:
	And don't pinch the keyboard wires putting the case back together.		And don't pinch the keyboard wires putting the case back together.

	== More Details from ~~RickHanson~~ on the T200 ==		== More Details from Rick Hanson on the T200 ==

	Flip the system over, turn off the MEMORY POWER and remove the four		Flip the system over, turn off the MEMORY POWER and remove the four

64.81.88.222: /* More Details from Rick on the T200 */

2008-03-10T05:18:19Z

More Details from Rick on the T200

← Older revision		Revision as of 22:18, 9 March 2008
Line 20:		Line 20:
	And don't pinch the keyboard wires putting the case back together.		And don't pinch the keyboard wires putting the case back together.

	== More Details from ~~Rick~~ on the T200 ==		== More Details from RickHanson on the T200 ==

	Flip the system over, turn off the MEMORY POWER and remove the four		Flip the system over, turn off the MEMORY POWER and remove the four

64.81.88.222: New page: == SPLITTING THE MODEL 100 CASE (The 102 and 200 split the same way) == From the Club 100 support files (www.club100.org)... There is a trick to splitting the Model 100 case: The two hal...

2008-03-10T05:17:07Z

New page: == SPLITTING THE MODEL 100 CASE (The 102 and 200 split the same way) == From the Club 100 support files (www.club100.org)... There is a trick to splitting the Model 100 case: The two hal...

New page

== SPLITTING THE MODEL 100 CASE (The 102 and 200 split the same way) ==

From the Club 100 support files (www.club100.org)...

There is a trick to splitting the Model 100 case: The two halves of the case
are held together by plastic notches in the middle of the edges. After
removing the case screws you simply have to know where to push in on the case
edges to split the case.

Turn the Model 100 upside down, remove the screws at the four corners. Turn
it right side up, like you are going to use it. Grab the left hand edge and
rock it up onto its right hand edge. The bottom will be facing your left and
the top to your right.

Using your left hand, push down on the middle of the top edge of the bottom
half and the same on the front edge facing you ... again, pushing in on the
bottom half, only. With your right hand, pull the top half away from the
bottom. The unit will split like a clam shell and lay open, easily.

And don't pinch the keyboard wires putting the case back together.

== More Details from Rick on the T200 ==

Flip the system over, turn off the MEMORY POWER and remove the four
case screws.

Flip the system right-side-up.

Open the lid. In the middle under the LCD is a 4"ish wide
cover. Push in on the top where it addresses the LCD and pry down
... be careful not to mar the plastic. You should be able to do the
above with just your fingers ... yes, it will hurt like heck but do
not use a sledge hammer and crowbar ... that's not cool!

With the cover off use two hands (and your left foot and then hold
your head sideways) to pop the ribbon cable out of the LCD-side connector.

Press in on the middle-edges of the top case half to "pop" the little
plastic case holders and remove the case halves.

Removing the components from the bottom case-half should be obvious
... if not, you should not have even started this
adventure! Ouch! That was cruel, huh?

Splitting the top case-half: Remove the 4 screws that hold the
LCD-section hinges from the bottom section then separate the two.

The LCD-section is two parts that slide together. Figure it
out! The screen side slides downward from the back side. Once off,
remove the 4 screws that hold the LCD into the whatchamacallit.