Difference between revisions of "PC-8201 BANK2 32kB SRAM card"

From Bitchin100 DocGarden
Jump to: navigation, search
Line 1: Line 1:
  
 
== Add 32kB BANK 2 to your NEC PC-8201 or PC-8201A ==
 
== Add 32kB BANK 2 to your NEC PC-8201 or PC-8201A ==
 +
 +
(for 16kB see below)
  
 
NEC originally shipped the PC-8201 / 8201A with only 16kB in Bank 1, but it can support 2 banks of 32kB.
 
NEC originally shipped the PC-8201 / 8201A with only 16kB in Bank 1, but it can support 2 banks of 32kB.
Line 61: Line 63:
  
 
[[Media:MEMCHK_NEC.zip|MEMCHK for NEC]]
 
[[Media:MEMCHK_NEC.zip|MEMCHK for NEC]]
 +
 +
 +
== 16kB Version ==
 +
 +
Bank 1 on the stock NEC PC-8201A was supplied with 16kB only.
 +
To upgrade this bank to a full 32kB, you can use a similar but smaller card.
 +
It plugs into RAM 2 and 3.  Same process and physical orientation as the 32kB card.
 +
 +
  
  
 
[[Category:Model T Hardware]]
 
[[Category:Model T Hardware]]

Revision as of 09:27, 7 November 2021

Add 32kB BANK 2 to your NEC PC-8201 or PC-8201A

(for 16kB see below)

NEC originally shipped the PC-8201 / 8201A with only 16kB in Bank 1, but it can support 2 banks of 32kB. These machines use the same SRAM modules as the Model 100, so to install Bank 2 you would need to buy 4 of these modules! Ouch!

This add-on card plugs into the SRAM sockets associated with Bank 2 - RAM 4,5,6 and 7 - and provides a full 32kB in one go!

There are two socket styles I have encountered - round pins (most common) or flat pins (less common). These are shown below.

PC-8201A

8201A STOCKs.jpg



PC-8201

8201 STOCKs.jpg


In these images you can see, as indicated by the red box, where the SRAM module should be placed. Also shown here - REX# for NEC is installed in the 8201A, in the Option ROM socket, and 8kB SRAM modules are installed in the RAM 2, 3 sockets of Bank 1.

Installation

  1.  Flip over the laptop and remove the memory compartment cover.
  2.  Align and orient the SRAM card over the sockets.
      You are installing a full 32kB in RAM 4,5,6,7.
  3.  Carefully press the SRAM card until it is fully seated in the sockets.
      Be careful not to bend the pins!
  4.  Reassemble the computer, turn on and run a memory test to confirm the installation is good!

Post-Installation Photos

PC-8201A


8201A SRAMs.jpg



PC-8201


8201 SRAMs.jpg


Memory Test

Here is Paul Globman's MEMCHK.DO (ported to NEC by yours truly). Load and run the .DO program. Remember, 1 beep means 'All good!'.

MEMCHK for NEC


16kB Version

Bank 1 on the stock NEC PC-8201A was supplied with 16kB only. To upgrade this bank to a full 32kB, you can use a similar but smaller card. It plugs into RAM 2 and 3. Same process and physical orientation as the 32kB card.